CBI Single Board Computer with the Intel Pentium III or Celeron Processor
If extended life-cycle requirements are important to your application, then the CBI makes sense. Both Hi-Tec's Technology and Intel's Applied Computing Products Division are providing long-term support for the CBI. So now you can maximize your equipment investment.
You'll get precise performance, too. No more than you need -- no less than you want. The CBI gives you a choice of an Intel Pentium III processor with blistering speeds or an Intel Celeron processor for solid performance at a reasonable cost -- whichever fits your needs.
Either way, Hi-Tec's dependable engineering and customer service make the CBI single board computer a long-term winner.
Processor: Intel Pentium III microprocessor at
600EMHz - 850MHz Intel Celeron microprocessor at 433MHz -
667MHz
Processor Package: Pentium III or Celeron processor in a
low-profile Socket 370 compatible package
Chip Set: Intel 440BX
AGPset with the Accelerated Graphics Port (AGP)
interface
System/Memory Bus: Intel 440BX AGPset supports the
system/memory buses at both 66MHz and 100MHz speeds. The 100MHz system/memory
buses provide a higher bandwidth path for transferring data between main
memory/chip set and the processor.
Concurrent PCI: Maximizes
system performance with simultaneous processor, PCI and AGP Bus activities. It
includes multi-transaction timing, enhanced write performance, a passive release
mechanism and support for PCI 2.1 compliant delayed transactions.
Data
Path:
|
Data/Memory
|
- 64-bit
|
ISA
|
- 16-bit
|
PCI
|
- 32-bit
|
Video
|
- 64-bit
|
| | | | Bus Speed:
|
ISA
|
- 8MHz
|
(All Speeds)
|
PCI
|
- 33MHz
|
(All Speeds)
|
System/Memory
|
- 66MHz
|
(Celeron)
|
|
- 100MHz
|
(Pentium III)
|
| | | | BIOS (Flash): AMI Hi-Flex BIOS with
built-in advanced CMOS setup for system parameters, peripheral management for
configuring on-board peripherals, PCI-to-PCI bridge support, and PCI interrupt
steering. Supports flash devices for BIOS upgrading via floppy interface. Custom
BIOSs available.
Cache Memory (L2): Pentium III - A 256K
integrated on-die Advanced Transfer Cache. The cache is 256-bit wide, 8-way set
associative cache running at full processor core frequency.
Celeron - A
128K integrated on-die 64-bit wide, non-blocking cache.
DRAM
Memory: The SDRAM interface consists of two dual in-line memory module
(DIMM) sockets and supports auto detection of memory up to 512MB of Synchronous
DRAM (SDRAM) memory. Minimum memory size is 8MB. The DIMM memory is PC-100
compliant for all speeds, which means that they comply with Intel's PC SDRAM
specifications. Uses industry standard 64-bit (non-ECC) or 72-bit (ECC) wide
gold finger DIMM DRAM in two 168-pin DIMM sockets.
Memory
Hole: Supports a 1MB memory hole option at 15-16MB.
Error
Checking and Correction: The memory interface supports ECC modes via BIOS
setting for multiple-bit error detection and single-bit error
correction.
PCI Local Bus Interface: Fully compliant with the
PCI Local Bus 2.1 Specification. This board has optimized the PCI interface to
allow the processor to sustain the highest possible bandwidth (greater than
100MB/sec sustained) and supports PCI-to-PCI bridge
technology.
Universal Serial Bus (USB): Supports two USB 1.0
ports for serial transfers at 12 or 1.5Mbit/sec. The Universal Serial Bus is an
interface allowing for connectivity to many standard PC peripherals via an
external port.
System Hardware Monitor: Provides monitoring of
system voltages, temperature and fan speed.
Floppy Drive
Interface: Supports up to two floppy disk drives in combinations of 360K
to 2.88MB.
AGP Super VGA Interface: The 69000 video interface
is an Accelerated Graphics Port (AGP) device with 2MB of on-chip memory. AGP is
designed to off-load the PCI Bus by allowing graphics data to move directly from
system memory. The interface supports pixel resolutions up to 1280 x 1024
non-interlaced. Software drivers are available for most popular operating
systems.
Serial Interface: Two high speed FIFO (16C550) serial
ports with independently programmable baud rates. Each serial port has BIOS
selectable addressing.
PCI 10/100Base-T Ethernet Interface: The
PCI Ethernet interface (Intel 82559) supports 10/100Base-T via an RJ-45
connector on the board's I/O bracket. The interface is compliant with IEEE 802.3
and PCI Local Bus 2.1 Specifications. Link status and activity LEDs are on the
I/O bracket. Software drivers are available for most popular operating
systems.
PCI Ultra Wide SCSI Interface: The SCSI interface is a
PCI Bus Master device using the Adaptec AIC-7880 chip. Supports Ultra Wide SCSI
operation up to 40MB per second and bursts data to the host at full PCI speeds.
Enable/disable active termination is provided with terminator voltage protected
by self-resetting fuses. Software drivers are available for most popular
operating systems.
PCI EIDE Ultra DMA/33 Interface (Dual): Dual
high performance PCI Bus Master EIDE interfaces are capable of supporting up to
four IDE Type 4 disk drives in a master/slave configuration. Supports Ultra
DMA/33 with synchronous DMA mode transfers up to 33MB per
second.
Watchdog Timer: The software controlled watchdog timer
monitors system activity and generates a reset pulse in the event of a
time-out.
Enhanced Bi-Directional Parallel
Interface: Compatible with PC/AT bi-directional parallel port and
supports EPP and ECP modes. The ECP mode is IEEE 1284 compliant. Parallel port
has BIOS selectable addressing.
PS/2 Mouse
Interface: Compatible with a PS/2-type mouse. Accessible via the I/O
bracket or off-board cabling. Mouse voltage is protected by a self-resetting
fuse.
Keyboard Interface: Compatible with AT-type keyboard.
Accessible via the I/O bracket or off-board cabling. Keyboard voltage is
protected by a self-resetting fuse.
Power Fail
Detection: Issues a hardware reset when on-board voltage drops below 4.75
volts.
Battery: Built-in lithium battery for ten years of data
retention for CMOS memory.
Power Requirements:
|
+5V
|
- 5.4 Amps typical (366MHz)
|
+12V
|
- < 100 mAmps typical
|
-12V
|
- < 100 mAmps typical
|
| | | Temperature:
|
Operating:
|
| 0
° - 60° C.
|
|
|
(0° - 55° C. for 700MHz Pentium III and above)
|
|
|
|
|
Storage:
|
|
- 40° - 70° C.
|
| | | Mean Time Between Failures (MTBF): 66,000
POH (Power-On Hours) at 40° C., per MIL-HDBK-217F
|
Model Name: CBI
|
|
Model #
|
CPU Speed
|
|
Pentium III:
|
|
|
5721-108-xM
|
850MHz
|
5721-107-xM
|
800MHz
|
5721-105-xM
|
700MHz
|
5721-103-xM
|
600EMHz
|
Celeron:
|
|
|
5721-012-xM
|
667MHz
|
5721-009-xM
|
566MHz
|
5721-005-xM
|
433MHz
|
| | | | | | | (xM = Memory)
|